Home
|
Learning Center
|
中文版
Publications
站内成果搜索:
搜索
Analysis on sliding velocity of cycloid gear pair during meshing
Analysis and improvement of SNR in FBG sensing system?
Analytical study on rock property of long-deep tunnel with CSAMT method
Analysis method for pile groups subjected to lateral and torsional loads
Analysis of subchannel reusable probability and capacity for frequency-reused femtocell networks under frequency partitioning strategy
Analysis and design of thin planar absorbing structure using Jerusalem cross slot
Analysis of phase on axis of the Bessel beam and self-imaged bottle beam
Analysis of contact stresses of wheel and rail with two types of profiles
Analysis of rolling contact and rail corrugation under non-steady state loading
Analysis on point-supported technology of the optical elements with large aperture
Analysis of laminar flow critical value for TiAl based alloy during centrifugal casting process
Analysis on inner defects in TiAl based alloy exhaust valve during the centrifugal foundry process in permanent mold
Analysis of micro-slotline leaky wave antenna with FDTD
Analytical modeling of Lamb waves in plate structures of aircraft
Analytical properties of axially loaded lightweight aggregate concrete filled circular steel tubular stub columns
Analysis of compliant micro-gripper and optimization design
Analysis on generalized measuring range of Fourier transform profilometry
Analysis of flexural capacities for RC members bonded with pre-tensioned FRP
Analysis of general stress and displacement in piezoelectric ceramics with an elliptic hole
Analysis of thickness uniformity of thin film deposited by magnetron sputtering system with multi-workbench
Analysis of the bend forming in pyrolysis process of polycarbosilane (PCS) fibers and effect on the properties of SiC fibers
Analysis model over data stream based on radial basis statistical network
Analysis of heat transfer enhancement within solar-powered flat plate adsorber
Analysis and simulation of the temperature distribution in electric tunnel furnaces
Analysis of winding arrangements of bearingless switched reluctance motors based on three-phase half-bridge power converter of the levitation windings
Analysis of toppling failure of rock slopes due to earthquakes
Analysis of wind-induced responses of dry coal sheds under interference condition
Analysis of isolating ground vibration induced by trains running on saturated ground
Analysis of the dynamic response of steel-deck pavement with roughness
Analysis on water consumption in oases of the Tarim Basin
Analysis of the damage of CRCP+AC composite pavement under thermal-mechanical coupling conditions by FEM
Analysis and solutions for multitasks scheduling in distributed environments
Analysis on rubs of double rotor-stator coupling system
Analysis on the oxidation behavior of Mo5Si3MoSi2/SiC multi-coating at high temperature
Analytical solution of combined heat and mass transfer processes of cross-flow dehumidifier using liquid desiccant
Analysis of mechanical characteristic for switch proper of turnout
Analysis for detectability and discrimination technology of space tracking and surveillance system
Analysis, modeling and correction of pointing errors for electro-optical detection systems
Analysis for geometrical nonlinearity with Element-free Galerkin Method
Analysis and design of for paralleled inverter system based on the small signal model using time-varying phasor
Analytical solution of magnetoelastodynamics'problem in the anisotropic thick-walled cylinder
Analysis of dam heel cracking in high arch dam based on deformation reinforcement theory
Analysis of structure stability and reinforcement based on deformation reinforcement theory
Analysis of aerodynamic load effects on thin plat section under active control flow condition
Analysis of the kinetic theory of submerged abrasive water jets
Analysis and prevention of geologic disasters caused by leakage in tunnel construction - Taking Huanshanping span tunnel as an example
Analysis of SO2 pollution in iron and steel industry city
Analysis on stability of dynamic supply chain
Analysis on driving process of steel piles by back analysis method
Analyzing the characteristics and better utilization of micro programmable diffraction grating
Analysis of effect of short circuit fault on 220 kV partial grounding transformer
Analysis of spatial and temporal variations of groundwater level and its salinity in Hetao Irrigation District
Analysis of mildiomycin and its derivatives from the culture filtrate of Streptoverticillium rimofaciens ZJU5119
Analysis of the moment capacity for FRP reinforced concrete beams
Analysis method of DVR compensation strategy based on load voltage and minimum energy control
Analysis of casing equivalent collapse resistance in creep formations
Analysis of influences of the error on the gear stiffness
Analysis of time effect on load-settlement behavior of driven piles
Analysis for geometric features of assembly objects in assembly process
Analysis of the interaction between deep excavation and adjacent existing tunnel
Analysis of degradable films'; pyrolysis and infrared spectrum characters
Analysis of chaotic phenomena in the fiber laser
Analysis of HVDC linear ground electrode system
Analysis and elimination of errors in phase diversity wavefront sensing system
Analysis on the design of short vertical grounding rods using numerical algorithm
Analysis of blasting vibration intensity based on finite element numerical calculation
Analytical model for the dispersion of sub-threshold current in organic thin-film transistors
Analysis and specification of DC side voltage in static var generator regarding compensation characteristics
Analysis method for Stewart platform workspace based on two-dimension search
Analysis on stress characteristics of rotating machine with cylinder body
Analysis of molecular weight distribution and root mean square radius of amylose from rice starch
Analysis of grading ring configuration for composite insulators on transmission tower
Analysis of vibrating compactor system involving slowly varying parameters of compacted material
Analysis and optimization of different mixing method in completly mixed digesters
Analysis of a forced vibration system with asymmetrical hysteresis
Analysis on dynamic characteristics of aero-engine high-speed ball bearings
Analysis of three-phase inverter based on instantaneous symmetrical components
Analysis and experiment of star-point controller in HVDC
Analysis of scattering properties for magnetic absorbing particles at the radar wave band
Analysis of combustion by-products of coal sludge with additives injection
Analysis of the Symbolism in The loons
Analysis on soil and lattice framed anchor structure interaction
Analysis on bearing capacity and ductility performance of transfer columns in SRC-RC hybrid structures